- 您现在的位置：买卖IC网 > Sheet目录204 > ASQ10817 (Panasonic Electric Works)SWITCH SNAP LEVER SPDT .1A PCB
ASQ1
6. Wire leads left side type: Mounting hole 3mm, standard type
mm General tolerance: ±0.25
CAD Data
R 0.5
C 0.3
1.9 dia.
8.4 ± 0.2
5.4 ± 0.15
2.7
5.4
13.3
3.2 ± 0.1
?
3.0 + 0.1
5.1 5.9
R 0.5
4.5
1.4 dia.
8.3 ± 0.1
3.7
4.3
5.2
5.0 ± 2
300 ± 10
R 0.5
2.4
3.0 + ? 0 0.1 dia.
? Wire lead thickness :
0.3mm 2
NOTES
Wire lead color
:
:
:
COM ···· Black
NC ······· Red
NO ······· White
1. Soldering conditions
1) To secure the switch, please use an
Plunger/Lever pushed
The application of excessive heat upon
the switch when soldering can cause
degradation of switch operation.
Therefore, be sure to keep within the
conditions given below.
1) Manual soldering: use soldering irons
(max. 350°C, within 3 seconds) capable
of temperature adjustment. This is to
M3 small screw on a ?at surface and
tighten using a maximum torque of 0.29
N·m. It is recommended that spring
washers be used with the screws and
adhesive be applied to lock the screws to
prevent loosening of the screws. Please
make sure not to apply adhesive onto the
moving parts.
Actuator
Pin
plunger
Leaf lever
Simulated
leaf lever
From mounting
boss and hole
center line
7.8 to 5.9
8.4 to 6.2
11.1 to 8.7
From standoff
12.0 to 10.1
12.6 to 10.4
15.3 to 12.9
prevent deterioration due to soldering
heat. Care should be taken not to apply
force to the terminals during soldering.
2) Automatic soldering: Soldering must
be done as below;
260°C: within 6 seconds
350°C: within 3 seconds
2. Mounting
Please avoid use in which load would be
applied to the sides (hatch part (both
sides) shown below) of the switch in the
direction indicated by the arrows. This
could cause erroneous operation. Also,
when using a metal installation board,
please make allowance for burr direction
designation and burr suppressing, etc.,
so that the burr side will not be on the
2) Be sure to maintain adequate
insulating clearance between each
terminal and ground.
3) Although it is possible to directly
operate the pin plunger type from the
lateral direction, please consult us if
doing so.
4) After mounting please make sure no
tensile load will be applied to the switch
terminals.
5) Range of possible use: Please set the
operation position to within the ranges in
the following table so that there is
suf?cient insulation distance and to
maintain contact reliability.
mm
Plunger/lever free
6) PC board terminal type should be
used if the products are to be soldered on
the PC board. Solder terminal type is not
for soldering on PC board.
3. Cautions regarding the circuit
1) In order to prevent malfunction in set
devices caused by bounce and chattering
during the ON-OFF switch operation,
please verify the validity of the circuit
under actual operating conditions and
temperature range.
2) When switching inductive loads
(relays, solenoids, buzzers, etc.), an arc
absorbing circuit is recommended to
protect the contacts.
4. Please verify under actual
conditions.
switch installation side.
Actuator
Pin
plunger
Leaf lever
Simulated
leaf lever
From mounting
boss and hole
center line
>9.2
>10.7
>13.5
From standoff
>13.4
>14.9
>17.7
Please be sure to conduct quality
veri?cation under actual operating
conditions in order to increase reliability
during actual use.
5. Switch selection
Please make your selection so that there
will be no problems even if the operating
characteristics vary up to ±20% from the
standard values.
Panasonic Corporation
Automation Controls Business Unit
industrial.panasonic.com/ac/e
AECTB6E 201201-T
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
AT-41.600MAGQ-T
CRYSTAL 41.600 MHZ 10PF SMD
AT079C
SW CAP SCREW-ON .394" RND RED
AT45DCB008
DATAFLASH CARD 8MEGABYTE
AT480CC
CAP SPOT ILL SQ RED W/LED LB SER
ATB322515-0110
TRANSFORMERS
ATE2DGPC104
SWITCH TOGGLE DPDT 0.4VA T/H
ATE2DGRA104
SWITCH TOGGLE DPDT 0.4VA T/H
ATP245SM
CRYSTAL 24.576 MHZ SERIES SMD
相关代理商/技术参数
ASQ10818
功能描述:基本/快动开关 SWITCH SNAP LVR SPDT .1A PCB
RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel
ASQ11510
功能描述:基本/快动开关 SPDT Pin Plunger PCB
RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel
ASQ11510J
制造商:Panasonic 功能描述:Bulk
ASQ11517
功能描述:基本/快动开关 SPDT Leaf LVR PCB
RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel
ASQ11518
功能描述:基本/快动开关 SPDT 1mA to 100mA Simultd. Leaf Levr
RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel
ASQ11518J
制造商:Panasonic Electric Works 功能描述:
ASQ14410
功能描述:基本/快动开关 SPDT Pin Plunger Solder
RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel
ASQ14417
功能描述:基本/快动开关 SPDT Leaf LVR Solder
RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel